When your bathroom renovation plumbing is done correctly, you’re not just getting new fixtures. You’re getting water pressure that actually works when someone flushes the toilet downstairs. You’re getting drains that clear in seconds, not minutes. You’re getting a shower that maintains temperature without scalding you mid-rinse.
Most importantly, you’re avoiding the nightmare of tearing into walls twice because someone didn’t route pipes correctly the first time. That’s not just about money—it’s about not living in construction chaos longer than necessary.
The difference between a bathroom that works and one that constantly needs attention comes down to how the plumbing was installed during the remodel. Get it right now, and you’re looking at years of reliable use. Rush it or cheap out, and you’ll be calling plumbers back within months. That’s the reality in Turnbull, FL, where older homes and Florida’s water conditions don’t forgive shortcuts.
We’ve handled bathroom remodeling plumbing throughout Brevard County for over 15 years. We’re state-certified (CFC#1428379), family-owned, and we’re not trying to be the biggest company in Florida. We’re trying to be the one you’d actually recommend to your neighbor.
Carl, who runs our company, started plumbing at 16 and spent 20+ years in the military before bringing that same discipline to every bathroom renovation. That background shows up in how we work—on time, thorough, and we clean up after ourselves.
Turnbull homes, especially the older ones built before 1975, often have cast iron pipes that are corroding from the inside out. We’ve replaced enough of them to know what you’re dealing with before we even open the wall. That’s the advantage of working with someone who’s seen it all locally, not a franchise crew learning on your dime.
First, we assess your existing plumbing before anything gets demolished. That means checking water pressure, inspecting pipe condition, and identifying any hidden problems that’ll become expensive surprises mid-project. If you’ve got cast iron pipes from the ’70s, we’ll tell you now, not after your contractor has already framed everything.
Next comes the rough-in work—rerouting pipes, installing new supply lines, and positioning drain lines exactly where your new fixtures need them. This is where most bathroom remodels go wrong. Measurements matter. Slopes matter. Venting matters. Miss any of these, and your beautiful new bathroom won’t function properly.
After your tile and walls are finished, we return for fixture installation. Vanity plumbing, shower and tub replacement, toilet installation—everything gets connected, tested for leaks, and checked for proper operation. We don’t consider the job done until water flows correctly and drains clear fast. Then we test it again.
Ready to get started?
Bathroom remodeling plumbing covers everything from supply line installation to drain system upgrades. That includes vanity plumbing with proper shut-off valves, shower and tub replacement with correctly pitched drain lines, and toilet installation with wax rings that actually seal.
We also handle pipe rerouting services when your new layout doesn’t match the old one. Moving a toilet six inches sounds simple until you realize it involves cutting concrete, rerouting the main drain line, and ensuring proper venting. Same goes for relocating sinks or converting a tub to a walk-in shower.
In Turnbull, FL, we’re also replacing a lot of old cast iron pipes during bathroom renovations. These pipes corrode from the inside, causing slow drains and eventual leaks. If your home was built before 1975, there’s a good chance you’re dealing with this. Replacing them during a remodel—when walls are already open—makes way more sense than waiting for a pipe to fail later.
Water heater placement sometimes factors in too, especially if you’re adding a second bathroom or your current heater can’t keep up. We’ll tell you if your system can handle the additional demand or if you need an upgrade to avoid cold showers.
The rough-in plumbing—installing pipes before walls close up—typically takes one to two days for a standard bathroom. That’s assuming we’re not dealing with major pipe rerouting or cast iron replacement, which adds time.
Fixture installation at the end of your remodel usually takes another day. That’s when we install your vanity, toilet, shower, and tub after tile and walls are complete.
The real timeline variable is what we find when we open walls. Turnbull homes built in the ’60s and ’70s often have surprises—corroded pipes, improper venting, or previous repairs that weren’t done to code. We can’t quote an exact timeline until we see what’s actually behind your walls. But we’ll tell you immediately if we find something that’ll impact your schedule or budget, not three days later after you’ve already committed to other trades.
If your Turnbull home was built before 1975 and still has original cast iron drain pipes, yes—replace them while walls are open. Cast iron corrodes from the inside, and by the time you see problems, the damage is significant.
The corrosion creates rough interior surfaces that catch debris and cause chronic slow drains. Eventually, the pipe deteriorates enough to leak or collapse entirely. Replacing it during a planned renovation costs a fraction of what emergency replacement costs after a pipe fails and floods your home.
We replace cast iron with PVC during bathroom remodels. It’s code-compliant, won’t corrode, and will outlast everything else in your bathroom. The work involves cutting out old pipe, installing new drain lines with proper slope and venting, and pressure testing everything before walls close. It adds to your project cost, but it eliminates a major future problem. Most Turnbull homeowners who’ve dealt with cast iron failures wish they’d replaced it proactively.
Yes, but it’s not always simple. Moving a sink is usually straightforward—we reroute supply lines and extend the drain. Moving a toilet or shower involves more work because drain lines require specific slopes to function properly.
Toilets need a 3-inch drain line that slopes at least 1/4 inch per foot toward the main drain. If you’re moving a toilet more than a few feet, we’re likely cutting into the floor, rerouting the drain line, and potentially adjusting venting. In homes on slabs—common in Turnbull—this sometimes means breaking concrete.
Shower and tub replacement with new locations involves similar drain work plus supply line rerouting. We also need to ensure proper venting, which sometimes requires running new vent pipes through walls or the roof. The complexity depends on your home’s layout and where you want fixtures moved. We’ll assess your specific situation and tell you exactly what’s involved before you commit. Some moves make sense. Others cost more than they’re worth, and we’ll be straight with you about that.
At minimum, replace shut-off valves under sinks and behind toilets. Old valves seize up and fail when you need them most. New quarter-turn ball valves cost little during a remodel and save major headaches later.
Consider upgrading to pressure-balancing shower valves if you don’t have them. These prevent temperature spikes when someone flushes a toilet or runs water elsewhere in the house. Florida code requires them in new installations, and they’re worth adding even if not required in your remodel.
If your water pressure is weak, we can install a pressure-boosting system or upgrade supply lines from 1/2 inch to 3/4 inch where it makes sense. Low pressure is common in older Turnbull homes, especially if you still have galvanized steel supply pipes that have corroded internally. Replacing them with PEX during a bathroom renovation solves the problem permanently. We’ll also recommend water-efficient fixtures that maintain performance while reducing water bills—low-flow doesn’t mean low pressure if you choose quality fixtures.
Hire a state-certified plumber for the plumbing work, not just your general contractor’s “guy who does plumbing.” Florida requires licensed plumbers for a reason—bathroom plumbing involves code requirements that impact safety and function.
Make sure rough-in plumbing is inspected and approved before walls close. This isn’t optional bureaucracy. The inspection catches problems while they’re still easy to fix. After drywall and tile go up, fixing a drain that’s sloped wrong or a vent that’s improperly sized costs exponentially more.
Insist on pressure testing supply lines and drain lines before finishing work. We test at higher pressure than normal use to ensure connections won’t leak. A connection that holds under test pressure won’t fail under normal use. Also, take photos of pipe locations before walls close. You’ll want that documentation if you ever need to hang shelves or make future modifications. These steps sound basic, but skipping them causes most post-remodel plumbing problems we get called to fix.
A straightforward bathroom remodel with fixture replacement and minimal pipe work typically runs $2,500 to $5,000 for plumbing labor and materials. That assumes you’re keeping fixtures in roughly the same locations and pipes are in decent shape.
Moving fixtures, replacing cast iron pipes, or upgrading from a tub to a walk-in shower increases costs. Major reconfigurations with significant pipe rerouting can run $7,000 to $12,000 or more, depending on complexity and what we find behind walls.
The biggest cost variable is existing pipe condition. If we open walls and find corroded cast iron, outdated galvanized steel supply lines, or previous repairs that weren’t done to code, addressing those issues adds to the project. We provide detailed estimates after assessing your specific situation, and we’ll explain exactly what you’re paying for. Bathroom remodeling plumbing isn’t something you want to cheap out on—it’s literally the foundation of whether your renovation functions properly for the next 20 years or becomes a constant source of problems.
Local Resources
Useful Links
